Heart shaped gift box
If you have a ready-made template, then making a heart is not difficult. And if not? Then do it yourself! True, it is necessary to carefully measure each side, otherwise the article will not be assembled when it is pasted together. Therefore, if you possess assiduity and patience, then this model is the heart for you. For the manufacture of such crafts prepare a sheet of red paper. It is better to take the paper dense, but not thick. Then, when gluing crafts, you will not experience difficulties, and in the finished form the heart will keep its shape well. You will also need a ruler, a simple pencil, scissors, glue and a sheet of white paper.
The sequence of work The heart is a three-dimensional shape consisting of a broken line that forms 8 short faces 1.5 cm long and two long side faces 6 cm long. The heart thickness is 2 cm. In finished form, the heart height is 7 cm. and its width is 7.5 cm.Cut white heart out of white paper. To do this, fold the sheet in half.
Set aside up to 6 cm in an upward bend. This is the distance from the tip of the heart to the notch at the top From the top mark, draw a horizontal auxiliary line to the right. And from the same mark, sweep up the beam at an angle of 45 °. Measure a 1.5 cm length on this ray. This will be the notch face. From the end of this segment, draw a horizontal line 1.5 cm long to the right. This is one of the tops of the heart.
From the end of the second line, draw a 1.5 cm long line down at an angle of 45 °. To do this, place the ruler on the sheet so that the measured length is connected to the auxiliary horizontal line.
From the end of this segment, draw a line 1.5 cm long down. This is the side of the heart.
And now connect the end of the segment with the bottom mark on the fold.
Cut out a heart pattern.
Expand. Take control measurements: all short edges should be 1.5 cm long.
Take a leaf of red paper and lay it upright. Turn the paper on the wrong side. Spend in the middle of the sheet two vertical parallel lines, the distance between them should be 2 cm. This is the thickness of the heart.
Draw a horizontal line at the bottom, defining the bottom edge of the pattern.
Measure upwards up to 6 cm - a distance equal to the length of the lateral inclined face of the heart. Draw a horizontal line. Then measure on vertical lines another 8 segments (the number of faces) of 1.5 cm each. Connect them.
Attach the heart pattern with the side edge to the first short sector.
Gently circle with a pencil.
Do the same on the second side of the vertical lines.
Now you need to draw on the layout the details with which you glue the top and bottom parts of the heart together. To do this, on both sides of the vertical lines, draw two lines 0.5 cm away from them.
Fromdraw small lines of each small sector at a small angle to each other.
Connect them as shown on photo.
Then measure upwards a distance of 6 cm and connect both sides of the horizontal line Oh. On the sides of this rectangle, draw details for gluing the model.
Notice the photo. At the top and bottom of the template, also draw fasteners.
Cut out the blank. Cutting the heart, the place of its connection with the fastener, also cut.
You will have such a template.
Side fasteners bend up at an angle of 90 °.
All parts of the pattern also bend along drawn lines.
Start to glue the template. Glue each with a glue You have a side mounting trapezoidal part on the front side, and apply the side of the heart next to it sequentially. If you notice a slight discrepancy in size, trim it right away.
When you glue it to the side Allow one side of the heart to let the glue dry. You got such a box.
Now grease the upper side of the fasteners bent at a right angle and put the second part of the heart on them.
Make sure that all the faces match each other.
Here's a cut heart You did it well.
Date: 09.10.2018, 14:05 / Views: 54373
Volumetric coffee heart in a potDIY: 10 ideas how to transform clay pots this summerLeather handbag with zipperSingle and Twin Heating MatHow to get in shape in three months without a gymThe Simplest Oscilloscope from a Computer